Thermal Properties of Matter — Complete Notes
Subject: Physics • Class: 11 • Unit: Properties of Solids and Liquids
Place in the exam pattern: This chapter usually gives 1–2 questions — thermal expansion, specific heat and calorimetry, latent heat, conduction and the radiation laws (Wien, Stefan–Boltzmann, Newton cooling) are the most frequently asked parts. Most questions are numerical, so every formula below must be practised with numbers, not just read.
Temperature is a measure of the hotness or coldness of a body, and heat is the energy that is transferred from one body to another because of a temperature difference. This chapter explains how temperature is measured, why materials expand on heating, how much heat a change of state needs, and how heat travels by conduction, convection and radiation.
1. Temperature and Heat
- Heat is a form of energy. It always flows from a body at higher temperature to a body at lower temperature, until both reach the same temperature (thermal equilibrium). The SI unit of heat is the joule (J); the older unit is the calorie: 1 cal = 4.186 J (about 4.2 J).
- Temperature is related to the average kinetic energy of the molecules of a body — it tells the direction in which heat will flow, not how much total energy the body holds. A large cold body can hold more total internal energy than a small hot body, yet heat still flows from the hot to the cold one.
- Thermal equilibrium: when two bodies in contact stop exchanging net heat, they are in thermal equilibrium and have the same temperature. This is the basis of a thermometer — it comes into equilibrium with the body and shows that body's temperature.
- Temperature is measured through a physical property that changes uniformly with temperature — the volume of a liquid (mercury/alcohol thermometer), the pressure of a gas at constant volume (gas thermometer), or the electrical resistance of a wire (platinum resistance thermometer).
2. Temperature Scales
- Celsius scale (degree C): ice point = 0 degree C and steam point = 100 degree C, divided into 100 equal parts.
- Kelvin scale (K): the absolute scale. Absolute zero = 0 K = -273.15 degree C — the temperature at which molecular motion is minimum. There are no negative temperatures on the Kelvin scale. Relation: T (K) = t (degree C) + 273.15 (often 273 is used). Note — with kelvin we write only K, not "degree K".
- Fahrenheit scale (degree F): ice point = 32 degree F, steam point = 212 degree F, divided into 180 parts.
- Conversion formula: (t_C / 100) = (t_F - 32) / 180 = (T_K - 273.15) / 100, that is t_F = (9/5) t_C + 32 and t_C = (5/9) (t_F - 32).
- Celsius and Fahrenheit read the same at -40: -40 degree C = -40 degree F.
- Triple point of water — the temperature and pressure at which all three states of water (ice, water, vapour) coexist in equilibrium — is 273.16 K. The kelvin is defined from this point: 1 K = 1/273.16 of the triple-point temperature.
- For a temperature difference, 1 degree C interval = 1 K interval, so degree C and K can be interchanged in expansion and specific-heat formulas.
| Scale | Ice point (water) | Steam point (water) | Absolute zero |
|---|---|---|---|
| Celsius (degree C) | 0 | 100 | -273.15 |
| Kelvin (K) | 273.15 | 373.15 | 0 |
| Fahrenheit (degree F) | 32 | 212 | -459.67 |
3. Ideal-Gas Equation — the Basis of the Gas Thermometer
- For an ideal gas, P V = n R T, where P = pressure, V = volume, n = number of moles, R = universal gas constant (8.314 J mol^-1 K^-1) and T = absolute temperature (in kelvin).
- Constant-volume gas thermometer: with the volume held fixed, P is proportional to T (P/T = constant). The temperature is found by measuring the gas pressure. Extrapolating the pressure to zero gives absolute zero — this is how the existence of absolute zero is established.
- The gas thermometer is taken as the standard thermometer, because at sufficiently low pressure all gases behave alike and the reading is almost independent of the gas used.
- At this chapter's level, remember one rule: in gas-law questions the temperature must always be in kelvin, never in Celsius. (Detailed gas-law and thermodynamics questions belong to their own chapters.)
4. Thermal Expansion
- Almost all substances expand on heating — as the amplitude of molecular vibration grows, the mean intermolecular separation increases. They contract on cooling.
- Linear expansion: for a rod of length L heated by deltaT, the increase in length is deltaL = alpha x L x deltaT, where alpha is the coefficient of linear expansion, unit per K (or per degree C). So alpha = deltaL / (L x deltaT) — the fractional increase in length per unit length per degree rise. New length: L' = L (1 + alpha x deltaT).
- Area expansion: deltaA = beta x A x deltaT, where beta is the coefficient of area expansion and beta = 2 alpha.
- Volume expansion: deltaV = gamma x V x deltaT, where gamma is the coefficient of volume expansion and gamma = 3 alpha.
- Relation between the coefficients: alpha : beta : gamma = 1 : 2 : 3 (for isotropic solids). For metals, alpha is of the order of 10^-5 per K (copper 1.7 x 10^-5, aluminium 2.2 x 10^-5, steel about 1.2 x 10^-5 per K).
- Two-rod condition: if the difference in length of two rods of different metals is to stay constant with temperature, their increases in length must be equal: L1 alpha1 = L2 alpha2 — the famous questions of this chapter are built on this condition.
- Thermal stress: if a rod is prevented from expanding (both ends clamped), a stress develops: stress = Y x alpha x deltaT and force F = Y A alpha deltaT (Y = Young's modulus).
- Pendulum clock: in summer the pendulum's length increases, so the period T = 2 pi sqrt(L/g) increases — the clock goes slow; in winter it goes fast.
- Bimetallic strip: two strips of different alpha joined together bend on heating towards the metal of smaller alpha — used in thermostats.
- Liquids show only volume expansion. The apparent expansion of a liquid in a container = real expansion of the liquid − expansion of the container, because the container also expands. Gases expand far more than solids and liquids.
5. Anomalous Expansion of Water
- Most liquids expand steadily on heating, but water contracts on heating from 0 degree C to 4 degree C and expands beyond 4 degree C. This is the anomalous expansion of water.
- Hence the density of water is maximum at 4 degree C (1000 kg/m^3) and its volume is minimum there.
- Consequence: in winter a lake freezes at the surface, while denser 4 degree C water stays below — the ice layer acts as an insulator, so aquatic life survives underneath.
- On cooling below 4 degree C water expands, which is why pipes can burst on freezing and why ice floats on water (ice is less dense than water).
6. Specific Heat Capacity
- The heat needed to raise the temperature of a body by deltaT is: Q = m x s x deltaT, where m = mass and s is the specific heat capacity of the material.
- Definition: s = heat required per unit mass per unit temperature rise: s = Q / (m x deltaT), SI unit J kg^-1 K^-1.
- Heat capacity of the whole body: C = m x s = Q / deltaT, unit J/K. Defined per mole, it is the molar specific heat, unit J mol^-1 K^-1.
- The specific heat of water is very high: s = 4200 J kg^-1 K^-1 (1 cal g^-1 degree C^-1). That is why water is used as a coolant (car radiators, nuclear reactors) and in hot-water bottles — it absorbs a lot of heat without becoming very hot, and gives out a lot of heat without becoming very cold. Coastal climates stay moderate for the same reason.
- For gases, the specific heat depends on the process — it is different at constant pressure (Cp) and at constant volume (Cv) (developed in the gases chapter).
7. Calorimetry
- Principle of calorimetry: in an isolated system, heat lost by the hot body = heat gained by the cold body (conservation of energy), provided there is no change of state and no heat escapes.
- Final (equilibrium) temperature of a mixture: T = (m1 s1 T1 + m2 s2 T2) / (m1 s1 + m2 s2). For the same substance and equal masses, the final temperature is the simple average of the two temperatures.
- The measuring vessel is a calorimeter — usually of copper (copper's specific heat is low, so the vessel itself takes little heat). Heat taken by the vessel is counted through its water equivalent.
- While solving, write Q = m s deltaT for each body separately, set heat lost = heat gained, and keep the final temperature as the unknown — always check that the final temperature lies between the two initial temperatures.
8. Change of State and Latent Heat
- At fixed pressure, while a substance changes state (solid ↔ liquid ↔ gas) its temperature stays constant, although heat is being supplied or removed. The heat supplied does not raise the kinetic energy of the molecules — it is spent in breaking intermolecular bonds, raising their potential energy.
- Latent heat: the heat required per unit mass to change the state (at constant temperature): L = Q / m, unit J/kg. Hence Q = m L.
- Latent heat of fusion (Lf): for ice, Lf = 3.34 x 10^5 J/kg (80 cal/g). Latent heat of vaporisation (Lv): for water, Lv = 2.256 x 10^6 J/kg (540 cal/g) — much larger than Lf; that is why steam burns are more severe than burns from boiling water — steam releases this extra latent heat as it condenses.
- Heating curve: ice (below 0 degree C) → melting at 0 degree C (plateau) → water heating up → boiling at 100 degree C (long plateau) → steam. The lengths of the plateaus are in the ratio of the latent heats; on the sloping parts use Q = m s deltaT and on the plateaus use Q = m L — in multi-step questions, count every step separately.
- Melting point and boiling point are fixed at a given pressure. Raising the pressure raises the boiling point (the pressure-cooker principle); the melting point of ice falls slightly when pressure is raised.
- Evaporation takes place only from the surface, at all temperatures, and produces cooling (the fastest molecules escape, so the average kinetic energy falls) — this is why water in an earthen pot stays cool and why sweating cools the body. Boiling takes place throughout the liquid at one fixed temperature.
- Sublimation: some substances (camphor, dry ice) pass directly from solid to gas without becoming liquid.
9. Heat Transfer — Conduction
- Heat is transferred in three ways: conduction, convection and radiation.
- Conduction: transfer of heat between parts in contact, without any transfer of the particles of the medium. In metals the main carriers are the free electrons — which is why good electrical conductors are also good thermal conductors (silver and copper are the best; wood, plastic and air are insulators).
- In the steady state, the rate of heat flow through a rod/slab is: H = Q/t = K A (T1 - T2) / L, where K = thermal conductivity, A = area of cross-section, L = length/thickness, (T1 - T2) = temperature difference between the faces. The unit of K is W m^-1 K^-1.
- The larger the K, the better the conductor: for metals K is of the order of 10^2, for insulators (wood, wool, foam) of the order of 10^-2. In foam and wool it is the trapped air that is the real insulator — the K of air is extremely small.
- Temperature gradient = (T1 - T2)/L, unit K/m. In the steady state, the temperature falls linearly along a uniform rod and the heat current is the same at every cross-section.
- Thermal resistance: in analogy with electrical resistance, R_T = L / (K A), unit K/W, and H = (T1 - T2) / R_T. Temperature difference ↔ potential difference, heat current ↔ electric current, R_T ↔ R — this analogy is the key to combination questions.
- Series slabs: layers one after another — the heat current H is the same through all, and resistances add: R_T = R1 + R2 + ... For two layers (thicknesses L1, L2; conductivities K1, K2; same A), the interface temperature is: T = (K1 T1 / L1 + K2 T2 / L2) / (K1 / L1 + K2 / L2) — or simply solve H = K1 A (T1 - T)/L1 = K2 A (T - T2)/L2.
- Parallel slabs: slabs side by side — the temperature difference is the same across all, and currents add: 1/R_T = 1/R1 + 1/R2; for two slabs of the same L and A, the equivalent conductivity is K_eq = (K1 + K2) / 2 (for unequal areas, take the area-weighted average).
- Insulation: a thicker layer, a smaller K and a smaller A all reduce H. In double walls and double-glazed windows, the trapped air layer is the insulator.
10. Convection
- Convection: transfer of heat by the actual movement of the particles of the heated medium — possible only in liquids and gases (fluids).
- Natural convection: heated fluid expands → its density falls → it rises, being lighter; cold, denser fluid sinks in its place — convection currents are set up. Sea breeze, monsoon and atmospheric circulation run on this: by day the land heats faster, air over it rises, and cool air flows in from the sea.
- Forced convection: the fluid is driven by a fan or pump — coolers, radiator fans, and temperature regulation of the body by blood circulation.
- In vacuum, neither conduction nor convection is possible — the vacuum between the double walls of a thermos flask blocks both, and its silvered surfaces block radiation.
11. Radiation — Absorptivity, Emissivity, Kirchhoff, Wien, Stefan–Boltzmann, Newton Cooling
- Radiation: transfer of heat as electromagnetic waves (mainly infrared) — no medium is needed; the Sun's heat crosses the vacuum to reach the Earth this way. It is the fastest of the three modes (speed of light).
- Every body emits radiation because of its temperature, and absorbs a part of the radiation falling on it (the rest is reflected/transmitted).
- Absorptivity (a): absorbed radiation / incident radiation. Emissivity (e): emitting power of the body / emitting power of a blackbody at the same temperature; 0 ≤ e ≤ 1.
- Blackbody: an ideal body that absorbs all incident radiation of every wavelength (a = 1, e = 1) and emits the maximum possible radiation at a given temperature. A rough, lampblack surface is nearly a blackbody; a polished shiny surface is a poor absorber and a poor emitter. That is why light/white clothes are worn in summer and the inside of a solar cooker is painted black.
- Kirchhoff's law: at a given temperature and wavelength, a good absorber is a good emitter and a poor absorber is a poor emitter: emissivity = absorptivity (e = a), and the ratio of emitting power to absorptivity is the same for all bodies (equal to that of a blackbody).
- Wien's displacement law: in blackbody radiation, the wavelength of maximum intensity is inversely proportional to the temperature: lambda_m x T = b, where b = 2.9 x 10^-3 m K (Wien's constant). As the temperature rises, the peak shifts to shorter wavelengths — the changing colour of hot iron (red → orange → yellow → white) and estimating the temperature of stars from their colour both rest on this law.
- Stefan–Boltzmann law: the energy emitted per second per unit area by a blackbody is E = sigma x T^4, where sigma = 5.67 x 10^-8 W m^-2 K^-4 (Stefan's constant) and T is the absolute temperature (kelvin). Double the temperature → 16 times the emission. For a general body, E = e sigma T^4.
- Net radiative exchange with the surroundings: a body at T in surroundings at T0 loses energy per unit area at the net rate E_net = e sigma (T^4 - T0^4) — it loses if it is hotter than the surroundings and gains if it is colder.
- Newton's law of cooling: when the temperature difference is small, the rate of cooling of a body is proportional to the difference between its average temperature and the temperature of the surroundings: -dT/dt = k (T - T0) (k = cooling constant, depending on the surface and nature of the body). The working form for the time taken to cool from T1 to T2: (T1 - T2) / t = k [ (T1 + T2)/2 - T0 ] — that is, take the excess of the average temperature over the surroundings. The body cools fast at first and then slowly (the cooling curve is exponential). The law is the small-difference approximation of the Stefan law and also holds in forced convection.
12. Important Facts — One-Liners (for last-minute revision)
1. Heat vs temperature: heat is transferred energy (J); temperature measures the average kinetic energy of molecules; heat always flows from hot to cold.
2. Scale conversion: t_F = (9/5) t_C + 32; T = t_C + 273.15; -40 degree C = -40 degree F — the only point where the two scales agree.
3. Triple point: 273.16 K — the basis of the definition of the kelvin; absolute zero is 0 K = -273.15 degree C.
4. Gas thermometer: at constant volume, P is proportional to T; always use kelvin in gas-law questions.
5. Linear expansion: deltaL = alpha L deltaT; alpha for metals is of the order of 10^-5 per K.
6. Coefficient relation: alpha : beta : gamma = 1 : 2 : 3; beta = 2 alpha, gamma = 3 alpha.
7. Two-rod condition: if the length difference is to stay constant, L1 alpha1 = L2 alpha2.
8. Thermal stress: F = Y A alpha deltaT — the force developed in a clamped rod on heating.
9. Pendulum clock: in summer the length increases, the period increases — the clock goes slow.
10. Anomalous expansion of water: water contracts from 0 to 4 degree C; density is maximum at 4 degree C — a lake freezes from the top, not the bottom.
11. Specific heat: Q = m s deltaT; s of water = 4200 J kg^-1 K^-1 — very high, which is why water is an excellent coolant.
12. Calorimetry: heat lost = heat gained; the final temperature always lies between the two initial temperatures.
13. Latent heat: Q = m L; Lf of ice = 3.34 x 10^5 J/kg, Lv of water = 2.256 x 10^6 J/kg — temperature stays constant during a change of state.
14. Steam burns are worse than burns from boiling water, because steam also releases latent heat on condensing.
15. Conduction: H = K A (T1 - T2)/L; unit of K is W m^-1 K^-1; free electrons are the main carriers in metals.
16. Thermal resistance: R_T = L/(K A); in series, R_T values add and H is the same; in parallel, the temperature difference is the same and H values add.
17. Interface temperature (series layers): solve from K1 (T1 - T)/L1 = K2 (T - T2)/L2.
18. Convection occurs only in fluids; heated fluid rises because its density falls — the cause of the sea breeze.
19. Kirchhoff's law: good absorber = good emitter; for a blackbody, a = e = 1.
20. Wien's law: lambda_m T = 2.9 x 10^-3 m K; on heating, the peak shifts to shorter wavelengths.
21. Stefan's law: E = sigma T^4 (T in kelvin only); double the temperature → 16 times the radiation; net exchange is e sigma (T^4 - T0^4).
22. Newton's cooling: rate of cooling is proportional to (average temperature of the body − temperature of surroundings); in the time formula, take the average temperature, not the initial.
23. Thermos flask: the vacuum blocks conduction and convection; the silvered surfaces block radiation.
24. Temperature intervals: an interval of 1 degree C = an interval of 1 K — either works in expansion and specific-heat formulas, but T^4 and gas laws need absolute temperature in kelvin.
13. Common Mistakes — Watch Out
1. Using Celsius in Stefan's law: in E = sigma T^4, T is always in kelvin. 27 degree C means 300 K — putting 27^4 makes the answer wrong by orders of magnitude.
2. Mixing up the expansion coefficients: beta = 2 alpha and gamma = 3 alpha; using alpha for area or beta for volume is a common error. For the volume expansion of a sphere, gamma = 3 alpha applies.
3. Forgetting the two-rod condition: "the length difference is independent of temperature" means the increases are equal (L1 alpha1 = L2 alpha2), not that the total lengths are equal.
4. Using Q = m s deltaT during a change of state: on a plateau the temperature does not change — there Q = m L applies. In a multi-step question (ice → water → steam), count every step separately: warming, melting, warming again, then vaporising.
5. Not checking the final temperature in calorimetry: if the computed equilibrium temperature falls outside the two initial temperatures, the solution is certainly wrong. Also, if the cold body is ice, first check whether the available heat is enough to melt it fully; the final temperature can also be 0 degree C.
6. Taking the initial temperature in Newton's cooling: the time formula uses (T1 + T2)/2 − T0 — the average temperature over the interval, not the initial temperature.
7. Series vs parallel slab confusion: layers stacked one over another are in series (H the same, R_T adds); slabs side by side are in parallel (temperature difference the same, H adds) — check with the electrical-circuit analogy.
8. Unit of K: the unit of thermal conductivity is W m^-1 K^-1, not J m^-1 K^-1 — J/s = W; forgetting the per-second part is a common slip.
9. Direction of water's anomalous expansion: from 0 to 4 degree C water contracts, it does not expand; the density is maximum at 4 degree C, not at 0 degree C.
10. Identifying lambda_m in Wien's law: lambda_m is the wavelength of maximum intensity, not the average wavelength; and with b = 2.9 x 10^-3 m K, lambda must be in metres.
11. Dropping the emissivity: for a real body, E = e sigma T^4; dropping e gives the blackbody answer. Likewise, do not forget to subtract the surroundings' T0^4 in net exchange.
12. Temperature difference vs absolute temperature: for deltaT, degree C and K are the same, but for ratios (T1/T2) or T^4 only kelvin works — recognise the two situations separately.
Next step: after these notes, take the 30-question Objective Quiz of this chapter — including previous years' questions, with an explanation for every question.

