Units and Measurements — Complete Notes
Subject: Physics • Class: 11 • Unit: Physics and Measurement
Place in the exam pattern: Questions come from this chapter every year — dimensions and dimensional formulae, combination of errors, significant figures, and the least count of vernier calipers and screw gauge are the most frequently asked parts. Most questions are numerical or formula-based, so practise every formula below with numbers; do not only read them.
Measurement is the foundation of physics. To measure a physical quantity means to compare it with a standard quantity of the same kind — a unit. A measurement result has two parts: a numerical value and a unit. A unit must be universally accepted, of suitable size, unchanged with time and place, and easily reproducible. That is why one single system of units — the SI system — is used all over the world.
1. Physical Quantities and Systems of Units
- Fundamental quantities are independent and cannot be expressed in terms of one another: length, mass, time, electric current, thermodynamic temperature, amount of substance and luminous intensity — 7 in total.
- Derived quantities are formed by combining fundamental quantities, e.g. velocity (length/time), force, energy, pressure.
- Main systems of units: CGS (centimetre–gram–second), FPS (foot–pound–second) and MKS (metre–kilogram–second). The SI (International System of Units) is the extended and rationalised form of MKS and is the standard worldwide today.
2. SI Base Units
| Fundamental quantity | SI unit | Symbol |
|---|---|---|
| Length | metre | m |
| Mass | kilogram | kg |
| Time | second | s |
| Electric current | ampere | A |
| Thermodynamic temperature | kelvin | K |
| Amount of substance | mole | mol |
| Luminous intensity | candela | cd |
- Metre: the distance travelled by light in vacuum in 1/299,792,458 second.
- Kilogram: defined through the fixed value of the Planck constant; in practice mass is measured by comparison with standard masses.
- Second: the duration of 9,192,631,770 oscillations of the radiation from caesium-133 atom.
- Ampere: defined through the fixed value of the elementary charge.
- Kelvin: defined through the fixed value of the Boltzmann constant; 0 K = -273.15 degree C.
- Mole: contains exactly 6.02214076 x 10^23 elementary entities (Avogadro number).
- Candela: the unit of luminous intensity in a given direction.
3. Supplementary Units — Plane Angle and Solid Angle
- Plane angle: d(theta) = arc length / radius = ds / r. Its unit is the radian (rad). A full circle = 2 pi rad = 360 degree; 1 rad = 180/pi degree (about 57.3 degree).
- Solid angle: d(omega) = area / (radius)^2 = dA / r^2. Its unit is the steradian (sr). The solid angle of a full sphere = 4 pi sr.
- Both are ratios, hence dimensionless quantities — they have units but no dimensions. This fact is asked repeatedly: plane angle and solid angle have units but no dimensions. Angular speed, strain etc. also have the same (dimensionless) character as the solid angle where applicable.
4. Measurement of Length
- Direct measurement: metre scale (least count 1 mm), vernier calipers (0.1 mm or less), screw gauge and spherometer (0.01 mm or less).
- Parallax method — for large distances: the apparent shift in the position of an object when viewed from two different positions is called parallax. The distance between the two observation points is called the basis. If the basis is b and the parallax angle is theta (in radian), the distance is D = b / theta.
- The distance of the Moon is measured this way from two distant points on Earth. For nearby stars, the diameter of Earth's orbit (about 3 x 10^11 m) is taken as the basis.
- Parsec: the distance at which a basis of 1 AU subtends a parallax angle of 1 arcsecond (1 arcsec). 1 parsec = 3.08 x 10^16 m (about 3.26 light years).
- Light year: the distance travelled by light in one year = 9.46 x 10^15 m. 1 AU = 1.496 x 10^11 m.
- Very small lengths: 1 micrometre = 10^-6 m; 1 nanometre = 10^-9 m; 1 angstrom = 10^-10 m; 1 fermi = 10^-15 m. Molecular sizes are found by optical methods and diffusion experiments.
5. Measurement of Mass and Time
- Mass: usually measured by comparison with known masses on a common balance. Masses of atoms and molecules are measured with a mass spectrometer. Atomic mass unit: 1 u = 1.66 x 10^-27 kg (1/12 of the mass of a carbon-12 atom).
- Time: time intervals are measured with great accuracy by atomic clocks (caesium clocks). The second itself is defined through caesium-133 oscillations.
- The range and accuracy of any instrument are linked to its least count — a smaller least count means a finer measurement.
6. Vernier Calipers
- Least count / Vernier constant: LC = 1 MSD - 1 VSD, where MSD = one main scale division and VSD = one vernier scale division.
- If n VSD = (n - 1) MSD, then LC = 1 MSD / n. Example: if 10 VSD = 9 MSD and 1 MSD = 1 mm, LC = 0.1 mm = 0.01 cm. If 1 MSD = 0.1 mm and (N + 1) VSD = N MSD, then LC = 0.1/(N + 1) mm = 1/(100(N + 1)) cm.
- Reading: measurement = main scale reading + (coinciding vernier division x LC).
- Zero error: if, with the jaws closed, the vernier zero lies to the right of the main scale zero, the zero error is positive and is subtracted from the measured value; if to the left, it is negative and is added. Correct measurement = observed measurement - (zero error with sign).
7. Screw Gauge
- Pitch: the distance advanced by the screw in one complete rotation. In practice, pitch = distance moved on the main scale / number of rotations.
- Least count: LC = pitch / total number of divisions on the circular scale. Example: pitch 1 mm with 100 divisions gives LC = 0.01 mm; a least count of 0.01 mm with 50 divisions gives pitch = 0.01 x 50 = 0.5 mm.
- Measuring a diameter: diameter = main (pitch) scale reading + (coinciding circular division x LC). Example: main reading 0 mm, circular reading 52 divisions, LC = 0.01 mm (1 mm on the main scale = 100 circular divisions) gives diameter = 52 x 0.01 = 0.52 mm = 0.052 cm. With pitch 1 mm and 100 divisions on an error-free screw gauge, a main reading of 1 mm with the 63rd division coinciding gives diameter = 1 + 63 x 0.01 = 1.63 mm = 0.163 cm.
- Zero error of a screw gauge is checked with the jaws closed and corrected exactly as for vernier calipers.
8. Accuracy, Precision and Types of Errors
- Accuracy tells how close the measured value is to the true value; precision tells the resolution limit up to which the measurement is made (linked to the least count). A measurement can be precise yet inaccurate (e.g. an instrument with zero error repeatedly gives the same wrong value).
- Systematic errors occur in one direction only: instrumental errors (e.g. zero error, faulty calibration), environmental errors (changes in temperature, pressure), personal errors (e.g. carelessness about parallax). They can be reduced by care and correction.
- Random errors occur irregularly, both positive and negative — they arise from causes such as unpredictable fluctuations in temperature and voltage supply. They are reduced by taking the mean of many observations.
- Least count error is the uncertainty linked to the least count of the instrument; it is reduced by choosing an instrument of smaller least count.
- Gross errors arise from carelessness and can be avoided completely by care.
- For repeated observations a1, a2, ..., an, the best value is the mean a_mean = (a1 + a2 + ... + an)/n.
9. Absolute, Relative and Percentage Error
- Absolute error: the error in each observation = |a_mean - a_i|. The mean absolute error is the mean of all absolute errors. The result is written as: a = a_mean ± (mean absolute error).
- Relative error: delta_a / a_mean (mean absolute error / mean value).
- Percentage error: relative error x 100 = (delta_a / a_mean) x 100 percent.
- While writing the result, both the mean and the error are rounded to the same decimal places, and the rules of significant figures are applied.
10. Combination of Errors
| Operation | Result | Error rule |
|---|---|---|
| Sum x = a + b | x | Absolute errors add: delta_x = delta_a + delta_b |
| Difference x = a - b | x | Absolute errors add: delta_x = delta_a + delta_b (they do not subtract) |
| Product x = a x b | x | Relative errors add: delta_x/x = delta_a/a + delta_b/b |
| Quotient x = a / b | x | Relative errors add: delta_x/x = delta_a/a + delta_b/b |
| Power x = a^n | x | Relative error is multiplied by n: delta_x/x = n x (delta_a/a) |
| General x = a^p b^q / (c^r d^s) | x | Percentage error = p x (percentage error in a) + q x (in b) + r x (in c) + s x (in d) |
- Example 1: in P = a^3 b^2 / (c x sqrt(d)), if the percentage errors in a, b, c and d are 1, 3, 2 and 4 percent respectively, the percentage error in P = 3 x 1 + 2 x 3 + 1 x 2 + (1/2) x 4 = 3 + 6 + 2 + 2 = 13 percent. Do not forget to multiply by the powers (including 1/2 for sqrt(d)) — that is the key to this question.
- Example 2: for density rho = m / (pi r^2 l) with mass (0.4 ± 0.002) g, radius (0.3 ± 0.001) mm and length (5 ± 0.02) cm, the percentage error = (0.002/0.4) x 100 + 2 x (0.001/0.3) x 100 + (0.02/5) x 100 = 0.5 + 0.67 + 0.4 = nearly 1.6 percent.
- The maximum possible error is what is asked — so all contributions are added, never subtracted.
11. Significant Figures
- The reliable digits plus the first uncertain digit in a measurement are called significant figures. They express the precision of the measurement.
- Counting rules: (1) All non-zero digits are significant. (2) Zeros between two non-zero digits are significant. (3) In a number without a decimal point, trailing zeros are not significant (e.g. 12300 has 3, unless stated otherwise). (4) In a decimal number, zeros before the first non-zero digit are not significant (the leading zeros in 0.002050 are not counted). (5) Trailing zeros after the decimal point are significant (the last zero in 0.002050 is significant — total 4 significant figures: 2, 0, 5, 0). (6) A power-of-10 factor (such as x 10^3) is not counted in significant figures.
- Rounding off: if the digit to be dropped is less than 5, the preceding digit stays unchanged; if greater than 5, the preceding digit increases by 1; if exactly 5, the preceding digit is made even.
- Rule for addition/subtraction: the result keeps as many decimal places as the minimum decimal places among the given terms. Example: 9.99 m - 0.0099 m = 9.9801 m, but 9.99 has only 2 decimal places, so the result = 9.98 m.
- Rule for multiplication/division: the result keeps as many significant figures as the minimum significant figures among the given factors.
- Rule for the mean: the mean of repeated observations is written to as many significant figures as each observation has. Example: the mean of 3.33, 3.32, 3.34, 3.33 and 3.32 cm is 3.328 cm, but each observation has 3 significant figures, so the mean = 3.33 cm.
12. Dimensions of Physical Quantities
- The dimensions of a physical quantity are the powers to which the fundamental quantities (M, L, T, A, K, mol, cd) must be raised to express that quantity. Dimensions are written in square brackets [ ].
- Examples: velocity = [L]/[T] = [M^0 L T^-1]; acceleration = [M^0 L T^-2]; force = [M L T^-2]; work/energy = [M L^2 T^-2].
- The dimensional formula is the expression showing which fundamental quantities enter the quantity and to what powers.
| Physical quantity | Dimensional formula |
|---|---|
| Velocity, speed | [M^0 L T^-1] |
| Force | [M L T^-2] |
| Energy, work | [M L^2 T^-2] |
| Power | [M L^2 T^-3] |
| Pressure, stress | [M L^-1 T^-2] |
| Frequency | [M^0 L^0 T^-1] |
| Impulse | [M L T^-1] |
| Momentum | [M L T^-1] |
| Gravitational constant G | [M^-1 L^3 T^-2] |
| Planck constant h | [M L^2 T^-1] |
| Angular momentum | [M L^2 T^-1] |
| Moment of inertia | [M L^2 T^0] |
| Surface tension | [M L^0 T^-2] |
| Coefficient of viscosity | [M L^-1 T^-1] |
| Coefficient of thermal conductivity | [M L T^-3 K^-1] |
| Specific heat capacity | [M^0 L^2 T^-2 K^-1] |
| Electric charge | [M^0 L^0 T A] |
| Magnetic permeability mu_0 | [M L T^-2 A^-2] |
- Pairs with the same dimensions: work and torque, both [M L^2 T^-2]; impulse and momentum; pressure, stress, Young modulus and bulk modulus, all [M L^-1 T^-2]; Planck constant and angular momentum.
- Dimensionless quantities: strain, angle, solid angle, refractive index, relative density — all [M^0 L^0 T^0]. The gravitational constant G carries M to the power -1 — i.e. G is the mechanical quantity whose dimensional structure involves the reciprocal of mass (full dimensions [M^-1 L^3 T^-2]).
- Dimensions of energy/gravitational constant (E/G): [M L^2 T^-2] / [M^-1 L^3 T^-2] = [M^2 L^-1 T^0].
- If force [F], acceleration [A] and time [T] are taken as fundamental quantities, energy = force x distance and distance = acceleration x time^2, so the dimensions of energy = [F][A][T^2].
13. Dimensional Analysis and Its Applications
- Principle of dimensional homogeneity: in a correct equation, the dimensions of both sides must be equal, and only quantities of the same dimensions can be added or subtracted.
- Application 1 — checking an equation: the correctness of a formula can be checked by matching the dimensions of both sides (e.g. v = u + at is correct; s = ut + (1/3) a t^3 is inconsistent, because a t^3 has dimensions [L T], not [L]).
- Application 2 — conversion of units: n2 = n1 x (M1/M2)^a (L1/L2)^b (T1/T2)^c — changing a value from one system to another (e.g. 1 J = 10^7 erg).
- Application 3 — deriving a relation between quantities: by assuming the dependence of a quantity on others and comparing powers (e.g. the time period of a simple pendulum T proportional to sqrt(l/g)).
- Limitations: (1) Dimensionless constants (such as 2 pi, 1/2) cannot be found. (2) Equations involving trigonometric, exponential or logarithmic functions cannot be derived. (3) If a quantity depends on more than three fundamental quantities, the powers are not uniquely determined. (4) Different quantities with the same dimensions (work and torque) cannot be distinguished. (5) A dimensionally correct equation need not actually be correct.
14. Orders and Key Conversions
- Order of magnitude: expressing a quantity as the nearest power of 10; if the multiplier is less than 3.16 (sqrt(10)) the power stays the same, if greater, the power increases by 1. Example: mass of the electron 9.11 x 10^-31 kg — 9.11 > 3.16, so the order = 10^-30 kg.
- Key conversions: 1 inch = 2.54 cm; 1 mile = 1.609 km; 1 pound = 0.4536 kg; 1 atm = 1.013 x 10^5 Pa; 1 calorie = 4.186 J; 1 kWh = 3.6 x 10^6 J; 1 electron volt = 1.602 x 10^-19 J.
- Unit of thermal conductivity: from K = Q x d / (A x deltaT x t), the unit is W m^-1 K^-1 — not J m^-1 K^-1, because power (watt) already includes time.
15. Important Facts — One-Liners (for final revision)
1. Fundamental quantities are 7 in total; their SI units are m, kg, s, A, K, mol, cd.
2. Supplementary units: radian (rad) and steradian (sr) — both are dimensionless; the solid angle of a full sphere is 4 pi sr.
3. Plane angle and solid angle have units but no dimensions.
4. Parallax method: D = b / theta (theta in radian); for nearby stars the basis = diameter of Earth's orbit.
5. 1 parsec = 3.08 x 10^16 m (about 3.26 light years); 1 light year = 9.46 x 10^15 m; 1 AU = 1.496 x 10^11 m.
6. 1 u = 1.66 x 10^-27 kg; 1 angstrom = 10^-10 m; 1 fermi = 10^-15 m.
7. Vernier least count: LC = 1 MSD / n, when n VSD = (n - 1) MSD.
8. Screw gauge: LC = pitch / number of circular divisions; pitch = LC x number of divisions.
9. Zero error: correct measurement = observed measurement - (zero error with sign).
10. Random errors arise from unpredictable fluctuations in temperature and voltage; they are reduced by taking the mean.
11. Form of the result: a = a_mean ± mean absolute error; percentage error = (delta_a / a_mean) x 100.
12. In sum and difference absolute errors add; in product and quotient relative (percentage) errors add; for a power n the relative error becomes n times.
13. Significant figures: 0.002050 has 4 significant figures; a power of 10 is not counted.
14. Addition/subtraction is governed by the minimum decimal places (9.99 - 0.0099 = 9.98 m); multiplication/division by the minimum significant figures.
15. Dimensions of stress are [M L^-1 T^-2] — the same as pressure and Young modulus.
16. Dimensions of G are [M^-1 L^3 T^-2]; dimensions of E/G are [M^2 L^-1 T^0].
17. Dimensions of mu_0 are [M L T^-2 A^-2]; dimensions of charge are [A T].
18. Work and torque have the same dimensions ([M L^2 T^-2]) — dimensional analysis cannot distinguish them.
19. Dimensional homogeneity: only quantities of the same dimensions can be added or subtracted; both sides of an equation must have the same dimensions.
20. Limitation of dimensional analysis: dimensionless constants (2 pi etc.) and relations involving sin/cos/log cannot be found.
21. Unit of thermal conductivity is W m^-1 K^-1; dimensions [M L T^-3 K^-1].
22. The mean is the best value of repeated observations and is written to as many significant figures as the observations have.
23. Order of magnitude: if the multiplier exceeds 3.16, the power of 10 increases by 1.
24. 1 J = 10^7 erg; 1 kWh = 3.6 x 10^6 J; 1 eV = 1.602 x 10^-19 J.
16. Common Mistakes / Points to Note
1. Subtracting errors in a difference: even for x = a - b, absolute errors add (delta_a + delta_b), they never subtract — the maximum possible error is the answer.
2. Forgetting the power multiplier: the percentage error of an r^2 term counts twice and of an a^3 term thrice; dropping the powers ruins questions such as density and P = a^3 b^2/(c x sqrt(d)).
3. Significant figures vs decimal places: addition/subtraction follows the decimal-places rule and multiplication/division follows the significant-figures rule — interchanging them is the commonest error (9.99 - 0.0099 gives 9.98, not 9.9801).
4. Counting leading zeros: in 0.002050 the leading zeros are not significant but the trailing zero is — the total is 4 significant figures, not 6.
5. Sign of vernier zero error: a positive zero error is subtracted and a negative one is added; reversing the sign pushes the corrected measurement further from the true value.
6. Confusing pitch with least count: pitch is the advance in one rotation; least count = pitch/number of divisions. Given LC 0.01 mm with 50 divisions, the pitch is 0.5 mm, not 0.01 mm.
7. Mixing radian and degree: in the parallax formula D = b/theta, theta must always be in radian; convert arcseconds first (1 arcsec is about 4.85 x 10^-6 rad).
8. Treating angle as dimensional: plane angle and solid angle are dimensionless — having a unit is not the same as having dimensions. For the same reason, the dimensions of strain are the same as those of solid angle (dimensionless).
9. Treating a dimensional check as sufficient: a dimensionally correct equation can still be wrong (a dimensionless constant may be missing); a dimensionally wrong equation is certainly wrong.
10. Writing the mean to extra figures: if observations have 3 significant figures, the mean is written as 3.33 cm, not 3.328 cm — extra digits claim false precision.
11. Forgetting powers in unit conversion: while converting area and volume the conversion factor also carries the power (1 m^2 = 10^4 cm^2, not 10^2).
12. Confusing accuracy with precision: a smaller least count improves precision; accuracy is closeness to the true value — a precise instrument with zero error can still give inaccurate results.
Next step: after these notes, take the 30-question Objective Quiz of this chapter — with previous years' questions and an explanation for every question.
