Mechanical Properties of Fluids — Complete Notes
Subject: Physics • Class: 11 • Unit: 7 — Properties of Solids and Liquids
Place in the exam pattern: Questions come from this chapter almost every year — pressure due to a fluid column, Pascal law and the hydraulic lift, Archimedes principle and floatation, the equation of continuity, Bernoulli theorem and the speed of efflux, viscosity with Stokes law and terminal velocity, and surface tension with excess pressure and capillary rise are the most frequently asked parts. Most questions are numerical, so every formula below must be practised with numbers, not just read.
Fluids are substances that can flow — liquids and gases. Unlike solids, a fluid has no fixed shape of its own; it takes the shape of its container and offers very little resistance to a change of shape. This chapter studies fluids at rest (pressure, buoyancy) and fluids in motion (continuity, Bernoulli theorem, viscosity), and ends with the surface behaviour of liquids — surface tension, excess pressure and capillarity.
1. Pressure — Due to a Fluid Column, Atmospheric and Gauge Pressure
- Pressure at a point is the normal force exerted per unit area: P = F / A. Its SI unit is the pascal (Pa): 1 Pa = 1 N/m^2. Pressure is a scalar quantity — at a point inside a fluid it has no single direction of its own; the force due to pressure at a surface is always normal to the surface.
- Density (rho) of a substance is mass per unit volume: rho = m / V, unit kg/m^3. The density of water is 1000 kg/m^3. Relative density (specific gravity) is the ratio of the density of the substance to the density of water at 4 degree C; it is a pure number with no unit.
- Pressure due to a fluid column: at a depth h below the free surface of a liquid of density rho, the pressure is P = P0 + rho g h, where P0 is the pressure acting on the free surface (usually atmospheric pressure). The term rho g h alone is called the gauge pressure at that depth.
- Pressure at a depth depends only on h, rho and g — not on the shape of the container or the total volume of liquid. All points at the same horizontal level in a stationary, connected liquid are at the same pressure (this is why the free surface of a liquid at rest is horizontal).
- Atmospheric pressure (P0) is the pressure exerted by the air column above us. At sea level it supports a mercury column 76 cm high: P0 = rho_Hg g h = 1.013 x 10^5 Pa (1 atm). It is measured with a barometer.
- Absolute pressure is measured from perfect vacuum; gauge pressure is the excess over atmospheric pressure: P_absolute = P_atmospheric + P_gauge. A pressure below atmospheric is sometimes quoted as a vacuum (negative gauge) pressure. Pressure in a fluid is measured with a manometer (open-tube or U-tube); for a U-tube, the pressure difference equals rho g x (difference of levels) of the manometer liquid.
- Because pressure grows linearly with depth, the force on a dam wall or on the base of a vessel grows with depth; the average pressure on a vertical wall of depth H is rho g H / 2.
2. Pascal Law and Its Applications
- Pascal law: pressure applied at any point of an enclosed (confined) fluid at rest is transmitted undiminished in all directions throughout the fluid and to the walls of the container. It holds for a fluid in equilibrium; the rho g h variation with depth is added separately.
- Hydraulic lift: two cylinders of areas A1 (small) and A2 (large) are connected and filled with an incompressible liquid. A force F1 on the small piston creates pressure P = F1 / A1, which is transmitted to the large piston, giving F2 = P A2 = F1 x (A2 / A1). Since A2 > A1, a small effort lifts a much larger load — the force is multiplied by the area ratio. Work is not created: the small piston moves through a larger distance than the load rises (volume displaced is the same, A1 x1 = A2 x2).
- Hydraulic brakes: pressing the brake pedal applies pressure to the brake oil in the master cylinder; Pascal law transmits this pressure equally to wheel cylinders of larger area, which press the brake shoes against the drums/discs with a multiplied force — all wheels brake together and evenly.
- The same principle works in the hydraulic press, hydraulic jack and earth-moving machinery.
3. Archimedes Principle, Buoyancy and Floatation
- When a body is wholly or partly immersed in a fluid, the fluid exerts an upward force on it called the buoyant force (upthrust). It acts because pressure increases with depth, so the upward pressure force on the lower parts of the body exceeds the downward force on the upper parts.
- Archimedes principle: the buoyant force on an immersed body equals the weight of the fluid displaced by the immersed part of the body: F_b = V_immersed x rho_fluid x g, acting upward through the centre of gravity of the displaced fluid (the centre of buoyancy).
- Apparent weight of an immersed body = true weight − buoyant force: W_app = W − F_b. A body weighed while immersed in a liquid always weighs less; the loss of weight equals the weight of the displaced liquid.
- Floatation: a body floats in equilibrium when its weight is exactly balanced by the buoyant force of the immersed part: W = F_b, that is, V_body x rho_body x g = V_immersed x rho_fluid x g. The fraction immersed is V_immersed / V_body = rho_body / rho_fluid.
- Conditions: if rho_body > rho_fluid, the body sinks (even fully immersed, F_b < W); if rho_body = rho_fluid, it remains in equilibrium anywhere inside the fluid; if rho_body < rho_fluid, it rises and floats with a part above the surface.
- Applications: ships (a steel hull floats because the hollow hull's average density is less than water, and the submerged part displaces water equal to the total weight), submarines (ballast tanks change the average density), hydrometers (the immersed fraction is smaller in a denser liquid, so the instrument floats higher; in a less dense liquid it sinks deeper, and the stem reading gives the density), icebergs (about 9/10 of ice, density about 900 kg/m^3, stays below water of density 1000 kg/m^3) and hot-air balloons.
4. Streamline Flow and the Equation of Continuity
- Flow is steady (streamline/laminar) when every particle arriving at a point follows exactly the path of the particle before it, with the same velocity; the velocity at any fixed point does not change with time. A streamline is the path traced by a fluid particle in steady flow; no two streamlines cross, and the tangent at any point gives the direction of velocity there.
- Streamlines crowd together where the fluid moves faster and spread out where it moves slower. Flow becomes turbulent — irregular, with eddies — when the speed is too high (see Reynolds number).
- Equation of continuity: for an incompressible fluid in steady flow, the volume flow rate is the same at every cross-section: A1 v1 = A2 v2 = constant. The quantity A v is the volume flow rate (m^3/s); the mass flow rate is rho A v. Hence the speed is inversely proportional to the area of cross-section — a river speeds up where it narrows, and a garden hose jet goes farther when the nozzle is partly closed.
- The continuity equation is simply the statement of conservation of mass for the flowing fluid.
5. Bernoulli Theorem and Its Applications
- Bernoulli theorem: for the steady, incompressible, non-viscous (ideal) flow of a fluid along a streamline, the sum P + (1/2) rho v^2 + rho g h = constant at every point of the streamline. Here P is the pressure energy per unit volume, (1/2) rho v^2 the kinetic energy per unit volume and rho g h the potential energy per unit volume — the theorem is the conservation of energy for moving fluids.
- For a horizontal pipe (h constant): P + (1/2) rho v^2 = constant — where the speed is higher, the pressure is lower. Combined with continuity (A v constant), a narrower section has higher speed and lower pressure.
- Torricelli law (speed of efflux): the speed of liquid flowing out of a hole at depth h below the free surface of a large open tank is v = sqrt(2 g h) — the same as the speed of a body falling freely through h. The volume flow rate is A_hole x v. The law assumes the tank is large, so the surface falls negligibly slowly.
- Venturimeter (concept): a horizontal tube with a narrow throat measures the flow speed/rate of a liquid. Pressure is lower at the throat (higher speed); the pressure difference between the wide part and the throat, read from a manometer, gives the speed through Bernoulli theorem and continuity together.
- Dynamic lift and everyday applications: (i) an aeroplane wing is shaped so that air moves faster over the top surface than below it; the lower pressure on top gives an upward lift; (ii) a spinning ball curves in flight (Magnus effect) because the spin makes the air speed, and hence the pressure, different on the two sides; (iii) roofs are blown off in a storm because the fast wind above the roof lowers the pressure there while the still air inside stays at higher pressure; (iv) two boats or trains passing close at speed can be drawn toward each other because the fluid between them speeds up and its pressure falls; (v) in an atomiser/spray pump, fast air over a tube lowers the pressure and liquid rises into the air stream. Blood flow and heart function are also described qualitatively with Bernoulli ideas, with viscosity corrections.
6. Viscosity
- Viscosity is the internal friction of a fluid: adjacent layers of a flowing fluid exert tangential forces on each other that oppose their relative motion. A viscous liquid (honey, glycerine, castor oil) flows slowly; a less viscous liquid (water, kerosene) flows quickly.
- For a layer moving over another, the viscous force is F = -eta A (dv/dx), where eta is the coefficient of viscosity, A the area of the layers and dv/dx the velocity gradient normal to the flow. The SI unit of eta is Pa s (also called the poiseuille, Pl); the CGS unit is the poise: 1 Pa s = 10 poise.
- Viscosity of liquids decreases with rise of temperature (cohesive forces weaken), while viscosity of gases increases with temperature. An ideal fluid has zero viscosity; viscosity also vanishes from Bernoulli theorem, which is why real liquids show small deviations from it.
- Because of viscosity, a body moving through a fluid experiences a retarding drag; for slow motion of a small sphere this drag is given by Stokes law (next section). Viscosity is also why the layer of liquid in contact with a pipe wall is at rest and the speed is maximum at the centre.
7. Stokes Law and Terminal Velocity
- Stokes law: a small sphere of radius r moving with velocity v through a viscous fluid of coefficient of viscosity eta experiences a viscous drag F = 6 pi eta r v, directed opposite to the motion. It holds for small spheres, low speeds (streamline flow around the sphere) and a fluid extending far around the sphere.
- Terminal velocity: a sphere falling under gravity accelerates until the sum of the buoyant force and the viscous drag balances its weight; after that it falls with a constant velocity — the terminal velocity. Balancing forces, with rho = density of the sphere and sigma = density of the fluid: v_t = (2/9) x r^2 (rho - sigma) g / eta.
- So terminal velocity is proportional to r^2, to the density difference (rho - sigma), and inversely proportional to eta. At terminal velocity the net force is zero and the viscous force equals weight − upthrust.
- If rho < sigma (density of the body less than the fluid), the body rises — for example, an air bubble in water rises with its own terminal velocity. Applications: raindrops reach a modest terminal velocity and do not keep accelerating to the ground; the Millikan oil-drop method and sedimentation use Stokes law; parachutes use large drag to keep the fall speed safe.
8. Reynolds Number
- The Reynolds number is the dimensionless number Re = rho v D / eta, where v is a characteristic speed of flow and D a characteristic length (for a pipe, its diameter). It estimates the ratio of inertial forces to viscous forces in the flow.
- Flow regimes for flow in a pipe (values as usually quoted): Re < 1000 — steady (streamline/laminar) flow; 1000 < Re < 2000 — the flow is unsteady and may switch between laminar and turbulent; Re > 2000 — turbulent flow. (Exact cut-offs vary slightly with the setup; the order of magnitude is what matters.)
- A low Reynolds number means viscosity dominates and the flow stays smooth and layered; a high Reynolds number means inertia dominates and the flow breaks into eddies. Reynolds number decides whether Stokes law and Bernoulli-type reasoning can be applied to a real flow.
9. Surface Tension and Surface Energy
- The free surface of a liquid behaves like a stretched elastic membrane and tends to contract to the minimum possible area. Surface tension (T) is the force acting per unit length on an imaginary line drawn on the liquid surface, acting tangentially and perpendicular to the line: T = F / l, unit N/m. It is also equal to the work done per unit increase in surface area.
- Surface tension arises from cohesion — the attraction between molecules of the same liquid. A molecule inside the liquid is pulled equally in all directions, but a molecule at the surface is pulled only inward and sideways, so the surface is in a state of tension and surface molecules have extra energy.
- Surface energy: increasing the surface area by delta A requires work W = T x delta A, which is stored as the extra potential energy of the surface. A soap film or soap bubble has two surfaces, so its surface energy is 2 T x (total area change); for a bubble of radius r, W = T x 2 x 4 pi r^2 = 8 pi r^2 T.
- Surface tension decreases with rise of temperature and falls to zero at the critical temperature; adding detergents or impurities also lowers it (which is why detergents spread water over clothes and clean better). Small liquid drops are spherical because a sphere has the minimum surface area for a given volume.
- Force due to surface tension on a body at the surface: a thin disc or ring of contact length l needs an extra force F = T x l to be pulled off the surface (for a disc, l is its circumference 2 pi r).
10. Excess Pressure Inside a Drop, a Bubble and a Curved Surface
- Because the surface is under tension, the pressure inside a curved liquid surface is greater than the pressure outside. The difference is the excess pressure.
- Liquid drop in air (one surface): delta P = 2 T / r. Soap bubble in air (two surfaces): delta P = 4 T / r. Air bubble inside a liquid (one surface): delta P = 2 T / r.
| Surface | Number of free surfaces | Excess pressure |
|---|---|---|
| Liquid drop in air | 1 | 2 T / r |
| Air bubble inside a liquid | 1 | 2 T / r |
| Soap bubble in air | 2 | 4 T / r |
- Excess pressure is inversely proportional to radius: smaller drops and bubbles have higher internal pressure. This is why, when two soap bubbles of different sizes are connected, the smaller bubble shrinks further and the larger one grows — air flows from the smaller (higher pressure) to the larger. It also explains why the pressure inside an expanding soap bubble decreases as it grows.
11. Angle of Contact and Capillarity — Capillary Rise
- The angle of contact (theta) between a liquid and a solid is the angle between the tangent to the liquid surface at the point of contact and the solid surface, measured inside the liquid. It depends on the nature of the liquid–solid pair (and on temperature and purity).
- If the adhesive force (liquid–solid attraction) exceeds the cohesive force (liquid–liquid attraction), the liquid wets the solid, the meniscus is concave and theta is acute (theta < 90 degree) — for example, water on clean glass, theta nearly 0 degree. If cohesion exceeds adhesion, the liquid does not wet the solid, the meniscus is convex and theta is obtuse (theta > 90 degree) — for example, mercury on glass, theta about 135 degree.
- Capillarity: the rise or fall of a liquid in a narrow tube (a capillary). Water rises in a glass capillary (concave meniscus pulls it up); mercury is depressed in a glass capillary (convex meniscus pushes it down).
- Capillary rise formula: for a tube of radius r, h = 2 T cos(theta) / (r rho g). The height is inversely proportional to the tube radius — narrower the tube, higher the rise. The mass of liquid in the tube, m = pi r^2 h rho, is therefore proportional to r: doubling the radius doubles the mass of the risen liquid (h halves, area becomes four times).
- Everyday capillarity: oil rises in a lamp wick, water rises from the soil to plant roots and through blotting paper and towels, and ink is drawn up in a pen — all through fine capillary spaces.
| Liquid–solid pair | Angle of contact | Meniscus | Behaviour in a capillary |
|---|---|---|---|
| Water — clean glass | Acute, nearly 0 degree | Concave | Rises |
| Mercury — glass | Obtuse, about 135 degree | Convex | Depressed (falls) |
| Water — wax/silver (non-wetting cases) | Obtuse | Convex | Depressed |
12. Important Facts — One-Liners (for last-minute revision)
1. Pressure: P = F/A, unit pascal; pressure is a scalar and the thrust on a surface is always normal to it.
2. Fluid column: P = P0 + rho g h; the rho g h part is the gauge pressure, and pressure at a given depth is the same in all directions and independent of the vessel's shape.
3. Atmospheric pressure: 1 atm = 1.013 x 10^5 Pa = pressure of a 76 cm mercury column; measured by a barometer.
4. Pascal law: pressure applied to an enclosed fluid is transmitted undiminished in all directions; hydraulic lift gives F2 = F1 x (A2/A1).
5. Archimedes principle: buoyant force = weight of fluid displaced = V_immersed rho_fluid g; apparent weight = true weight − buoyant force.
6. Floatation: fraction immersed = rho_body / rho_fluid; a body floats if its density is less than the fluid's, sinks if greater.
7. Continuity: A1 v1 = A2 v2 for incompressible steady flow — speed is inversely proportional to cross-sectional area.
8. Bernoulli: P + (1/2) rho v^2 + rho g h = constant along a streamline (steady, incompressible, non-viscous flow); faster flow means lower pressure.
9. Torricelli: speed of efflux v = sqrt(2 g h); volume rate = A_hole x sqrt(2 g h).
10. Venturimeter works on Bernoulli principle: the throat has higher speed and lower pressure.
11. Dynamic lift: a wing gets lift because air is faster above it and pressure there is lower.
12. Viscosity: F = -eta A (dv/dx); SI unit of eta is Pa s; liquid viscosity falls with temperature, gas viscosity rises.
13. Stokes law: drag on a small sphere F = 6 pi eta r v.
14. Terminal velocity: v_t = (2/9) r^2 (rho - sigma) g / eta; at terminal velocity weight = upthrust + viscous drag, net force zero.
15. Reynolds number: Re = rho v D / eta; below about 1000 flow is laminar, above about 2000 it is turbulent.
16. Surface tension: T = F/l = work per unit area increase, unit N/m; it falls as temperature rises.
17. Surface energy: W = T x delta A; a soap film/bubble has two surfaces, so a bubble of radius r needs W = 8 pi r^2 T to form.
18. Excess pressure: drop and air bubble in liquid: 2T/r; soap bubble: 4T/r — smaller the radius, larger the excess pressure.
19. Expanding bubble: as a soap bubble grows, its excess pressure (4T/r) decreases, so the inside pressure decreases toward atmospheric.
20. Angle of contact: acute and concave meniscus = liquid wets the solid (water–glass); obtuse and convex meniscus = liquid does not wet it (mercury–glass, about 135 degree).
21. Capillary rise: h = 2 T cos(theta) / (r rho g) — h is inversely proportional to r, and the mass of risen liquid is proportional to r.
22. Disc on water: extra force to lift a disc off the surface = T x circumference = 2 pi r T.
23. Ice in water: with densities 900 and 1000 kg/m^3, 9/10 of floating ice stays submerged.
24. Hydraulic brakes and lifts both multiply force by the piston-area ratio — Pascal law at work; no work is created, the small piston simply moves farther.
13. Common Mistakes — Watch Out
1. Treating pressure as a vector: pressure has no direction of its own; it is a scalar. Only the force it produces has a direction — always normal to the surface.
2. Forgetting atmospheric pressure: P = P0 + rho g h gives the absolute pressure. If a question asks for gauge pressure, do not add P0; if it asks for absolute pressure, do not omit it.
3. Pascal law without the depth term: in a tall vessel the rho g h variation still exists; Pascal law adds the applied pressure equally everywhere on top of the hydrostatic variation.
4. Buoyancy with the wrong volume or density: the buoyant force uses the immersed volume and the fluid's density — not the body's total volume (unless fully immersed) and never the body's density.
5. Floatation fraction inverted: fraction immersed = rho_body / rho_fluid (body over fluid). Writing it the other way up gives fractions greater than 1 for floating bodies, which is impossible.
6. Continuity with diameters: A is proportional to d^2, so halving the diameter quarters the area and makes the speed four times — not two times.
7. Applying Bernoulli to viscous or turbulent flow: the theorem needs steady, incompressible, non-viscous flow along one streamline; comparing points on different streamlines or in a honey-like liquid breaks it.
8. Efflux speed with the wrong h: in Torricelli law, h is the depth of the hole below the free surface, not the height of the hole above the ground.
9. Stokes law on big or fast bodies: F = 6 pi eta r v needs the radius (not diameter) and holds only for small spheres at low speed; putting the diameter in place of the radius makes the drag twice the correct value.
10. Terminal velocity sign: v_t uses (rho - sigma). If the body is less dense than the fluid, the result is negative in the downward sense — the body rises; do not report a negative speed as a fall speed.
11. Drop versus bubble factor: a liquid drop (and an air bubble in liquid) has one surface — 2T/r; a soap bubble has two surfaces — 4T/r and surface energy 8 pi r^2 T. Mixing the factors 2 and 4 is the commonest surface-tension error.
12. Capillary formula slips: h needs cos(theta) and the tube radius. For mercury theta is obtuse, cos(theta) is negative, and h comes out negative — meaning depression, not rise; dropping the sign hides the physics.
13. Reynolds number units: Re is dimensionless; do not attach units to it, and use the pipe diameter as the length in the standard formula.
Next step: after these notes, take the 30-question Objective Quiz of this chapter — including previous years' questions, with an explanation for every question.

